|
|
Temperature Profile in Reflow Soldering and Influence of Different PCBś and ComponentsThermal Capacities
Procházka, Martin ; Špinka, Jiří (referee) ; Starý, Jiří (advisor)
This thesis mainly deals with the prediction of temperature on the components and the PCB during reflow soldering. The theoretical part describes the particular solder reflow process, types of heat transfer and temperature profiles. The practical part is divided into forecasting temperatures if the conveyor is stopped and the temperature predictions when the conveyor is in motion. In both parts of the measured temperature is compared with the predicted temperatures, which show the success rate of prediction. The last part of this work is part of the simulation, which helps in proper understanding of the issues discussed.
|
|
|
Non-contact Temperature Measurement
Lata, Miroslav ; Janečka, Jan (referee) ; Vdoleček, František (advisor)
The object of this bachelor thesis was to create a study of development non-contact temperature measurement and show methods of measurement in infra-red radiation area. The beginning of this work is focused on major notions and definitions necessary to introduce non-contact temperature measurement topic. Other interest of this work was to mention possible error rate of measurement, it’s reasons then name some ways of calibration of a measuring equipment with it’s reasons too. Last part of this thesis was focused on a practical using of these measuring devices.
|
|
|
Study of thermal properties of selected coloids
Křivánková, Kateřina ; Krouská, Jitka (referee) ; Zmeškal, Oldřich (advisor)
The bachelor thesis is focused on the study of the thermal properties of colloidal systems, especially the properties of emulsions (water, oil), which can be used in the cosmetic industry as an essential component of various lotions and creams and in the food industry. In the introduction the first defined thermo-physical processes (conduction, convection and radiation) and temperature measurement (stationary, transient). Furthermore defined physical parameters (heat and thermal conductivity, heat capacity), that are determined using transient methods. The measured data were collected and analyzed by using the EMA (Electrical Measurement Analyser) and the HarFA (Harmonic and Fractal Image Analyser). The results will be used to determine the optimum conditions for the production of cosmetics and dietary supplements.
|
|
|
Methodology of temperature measurement behind jet engine
Koutný, Martin ; Koštial, Rostislav (referee) ; Matějů, Jiří (advisor)
This thesis is focused on temperature measurement behind jet engine. The theoretical part introduces chosen ways of temperature measurement. The practical part is divided into design (and later assembly) of the measuring stand, methodology of measurement and the measurement itself. The main outcome are heat maps gained by measuring temperatures behind TJ – 42 jet engine.
|
|
| |
|
|
Emisivity and its Impact on the Heat Conductivity
Gančev, Jan ; Hejátková, Edita (referee) ; Szendiuch, Ivan (advisor)
This work deals with the issue of emissivity and its impact on the heat dissipation.The first part describes the basics of thermal management, the issue of emissivity and its measurement. In the second, experimental part, are dedicated the emissivity values of examined specimens. These values are then used as initial conditions for the thermal simulation. In the last part are compared the measured results and the simulated results and is evaluated the impact of emissivity for the heat dissipation.
|
|
|
Temperature Profiles Measurement of SMD Packages
Strapko, Jaroslav ; Szendiuch, Ivan (referee) ; Starý, Jiří (advisor)
Diploma thesis mainly deals with temperature management and calculation of temperature profile in oven by using SMD packages (PLCC, 1206) of different thermal capacitance on testing PCB. Above all shows theoretical consecution of temperature profile calculation in oven by using known mathematical method like the lumped capacitance method or finite difference method. Theoretical solution and measured values are compared. Diploma thesis also deals with fixation methods of thermocouples K type on assembly, comparison methods based on known and subexperiment, determines the deficiencies of methods. This thesis can perform as theoretical as well as experimental resource to prediction of temperature profiles of PCB´s with different assembly density.
|
|
| |
|
|
Measurement of thermoelectric modules
Martynek, Filip ; Baláš, Marek (referee) ; Brázdil, Marian (advisor)
This thesis describes principles of thermoelectric change, crucial parameters of thermoelectric modules and issues of its measurements. Theoretical part of this research is aimed on describing thermoelectrical phenomena, composition of thermoelectric pair and modules, naming searched parameters and issues that occurred during its measurements. Further in detail describes chosen testing approaches. In the end these methods are concluded and compared. Practical part contains description of testing device and experimental measurement of thermoelectric module.
|
|
|
Fabrication and calibration of thermocouples
Balák, Martin ; Svoboda, Josef (referee) ; Foral, Štěpán (advisor)
This thesis is focused on the creation of laboratory task. The first part describes the operating principle of the thermocouple and according to which the physical laws are working. The thesis also shows the main categories of the division of thermocouple. Next chapter explains the composition of thermocouple welder, its main components and how the process of welding thermocouple wire is under way. The last chapter of the theoretical part is focused on the calibration of thermocouples. This chapter explains what the calibration is and it also shows the examples of calibration on real devices. The first part of the practical section describes the construction of the laboratory product and what materials were used for the given construction. The following part deals with the electrical interior of the thermocouple welder. Electrical diagram is described and there is also the description of how to direct and regulate the supply voltage and how it reaches the clamps of the capacitor. Its charging is observed by measuring instrument (voltmeter). The thesis works with the proper welding procedure, its potential problems, and the correct method of welding because the weld must be in sufficient quality in order to pass the calibration. This work also shows how the welds should not look and what to do in case they do not look well. The second part of the practical section deals with the comparison of welded thermocouples tested on produced product and on SR80 UWO. The three pieces of thermocouples were welded on each of them. Their following comparison is the proof of the quality of the welding preparation. The last part of the second practical part is focused on the calibration of the thermocouple prepared thanks to the product.
|
guest ::
